Deck Board Calculator
Enter the size of your deck and this works out how many boards to buy, compares every board length your yard stocks, and draws where each butt joint lands on a joist. It also counts the joists and the screws or hidden clips.
How many deck boards do I need?
Two numbers decide it: how many rows of boards it takes to cover the width, and how many boards it takes to make each row as long as the deck.
Rows. Each board covers its own width plus one gap. Divide the deck width in inches by that, and round up. A 12 foot wide deck in 5 1/2 inch boards with a 3/16 inch gap is 144 ÷ 5.6875 = 25.3, so 26 rows, and the last one gets ripped down to fit.
Boards per row. If a stock length covers the whole run, it is one board per row and no joints. A 16 foot deck in 16 foot boards is 26 boards. If the deck is longer than any board you can buy, each row needs two or more pieces joined end to end, and that is where most hand estimates go wrong: the joints can only fall on a joist, so you cannot use every inch of every board.
The usual shortcut, square footage divided by board coverage plus 10% for waste, gets you in the right area for a simple deck. The calculator above does the layout properly instead, joint by joint, and reuses offcuts where they are long enough to make another piece.
Which board length should you buy?
The table compares every length you ticked. Two things are traded off. Longer boards mean fewer joints, which look better and give water fewer places to sit. But the longest board is not always the cheapest, because what is left over from one row can become a piece in another, and some lengths divide into your deck far more cleanly than others.
The recommendation picks the fewest joints among the options within 10% of the cheapest linear footage. If you would rather spend the least on timber no matter how many joints, choose the row with the lowest linear feet instead. Click any row to see its layout.
Where the butt joints go
- On a joist, always. Both board ends need something to screw into. The calculator only places joints on a joist.
- Staggered. Joints in neighboring rows should not land on the same joist, or you get a seam running straight across the deck. The layout avoids that wherever the deck length allows it, and adds a joint rather than stacking one.
- No short pieces. Every piece spans at least two joist spacings, so it sits on three joists and does not rock.
- Give the ends room. Two board ends sharing one joist leaves little wood for the screws. Many builders add a block or a second joist beside it at each joint line.
The layout assumes the first joist sits at the start of the boards and the rest follow at your spacing, with a rim joist at the far end. If your framing is set out differently, move the joints to suit.
Board gaps
Pressure-treated boards often arrive wet from the treatment plant and shrink across their width as they dry, so many builders butt them tight and let the gap open up on its own. Kiln-dried lumber and hardwoods need the gap set at install, commonly 1/8 to 3/16 inch. Composite and PVC boards move with temperature rather than moisture, and each manufacturer publishes its own gap spec, so follow the install guide for the board you buy.
Joist spacing
16 inches on center is the common default for decking laid square to the joists. Many composite boards call for 16 inches or closer, and boards laid on a diagonal need the joists closer again because the span across them is longer. Check what your decking is rated for before you frame.
Screws or hidden fasteners
Face-screwed boards take two screws at every joist they cross, and two more wherever a joint puts two board ends on one joist. Hidden clip systems use roughly one clip per joist in every gap between rows, plus a starter and finishing fastener along each edge, and need boards with a grooved edge. The counts above are a starting point; buy a box over, because you will drop some.
For what to look for in a deck screw, see the guide to wood screws and fasteners.
What this does not cover
Picture-frame borders, diagonal or herringbone layouts, stairs and multi-level decks all change the arithmetic, and this calculator handles one rectangle of straight boards. For those, run each rectangle separately and add them up. Framing timber is a separate order too: the cut list calculator will turn joists, beams and blocking into a lumber list, and the lumber weight calculator tells you whether the delivery will fit in your truck. The full set of calculators is here.
Still planning the deck itself? The outdoor section of the Teds Woodworking pack covers decks, arbors, sheds and picnic tables.
Affiliate link, opens the offer in a new tab.